去43网看看，偶尔会有人出机身。

胖大住双井？

曝光不足

天气不好

我也想搞台成色新的L1...有的兄弟pm我

内牛满面呵, L1查快门数的方法终于被破解了

实在经不住诱惑, 照着试了一下, 果然是work的. 我的第二台L1共按了10980次快门, 闪了149次

具体方法如下, 其实很简单的.. 这个人废话比较多罢了.

So after much research on the web, I came across some interesting info concerning the service menu on the Leica Digilux 4... after applying the methods used to my Lumix DMC-L1, I've made my way into the service menu... if this has been covered already, I apologize as I couldn't find it.

Use at your own risk, as you could turn your camera into an expensive brick... let me know if it works for everyone!

Service Mode may allow you to do some kinds of operations which are  normally not available in the camera's menu:

(1) Reset the camera  to unboxing settings. (Not only to the factory default settings)
(2)  Reset the firmware region for supporting more languages, if applicable.
(3)  Check camera usage information.

YOU MAY WANT TO CONNECT TO AC POWER BEFOREHAND, I HAVEN'T HAD THE PRIVILEGE OF MY BATTERY DYING DURING THE PROCESS!

1. Turn off the camera.
2. Set the shutter speed dial to the 8 position.
4. Press and hold the AFL/AEL button.
5. While holding the AFL/AEL button turn on the camera.

You are now temporarily in the Service  Mode. You can confirm your status by checking the CUSTOM menu. There is  one more option named "SENSOR CLEAN" there, under the "NO RELEASE WITHOUT LENS" option.

The camera may return from this mode  to the normal mode by turning the power off and on again. After the  power cycling operation, the extra "SENSOR CLEAN" option will no longer be  available in the CUSTOM menu.

So what can you do once you are in  this temporary Service Mode?

You can check your firmware by pressing [Play], then pressing the [FUNC.2] and [DOWN ARROW] simultaneously .

Anything  else interesting under the Service Mode?

Yes, you may check the  usage information of your camera. At first, make sure you are in the  Service Mode, then follow the steps below to see the secret of your  camera.

1. Press and hold the [FUNC.2] button, then MENU/SET and ◀  (Left arrow) buttons together. The camera now shows a screen of zeros  on a white background. If you press the DISPLAY button, the camera will  cycle through three different content showing some kind of parameter  codes in decimal or hexadecimal form. The arrow  buttons can be used here to scroll through the code arrays.

(Guy Parsons, a Sydney  based LX3 owner, considered the first "Zero" screen as an Error  Code Log used for Panasonic service persons, and the explanation  should be in their Service Manual. He also revealed some of the counters  below.)

2. Again, press and hold the [FUNC.2] button, then MENU/SET  and ◀ (Left arrow) buttons together. The camera will show its usage  information in two pages. Press the DISPLAY button to  switch between the pages.

The camera information is  interpreted below:

VER 2.10:0210 -> Firmware  version is 2.20.
NO.:  F35XXXXXXXXXX -> A 12-digit number with a "F" prefix. (Motherboard  serial number?)
PWRCNT: 834 -> Power On Count, the number  of times camera turned on.
SHTCNT: 5873 -> Shutter Count,  the number of times shutter fired.
STBCNT: 80 -> Strobe  Count, the number of times flash fired.

1ST.:  2010.4.17 2:34 -> Date and time of first clock set.
A: 2010.4.18 8:47 -> Date and  time of last two clock sets.
B: 2010.4.18 8:39 ->  (See above)
ClockSet Cnt: 3 -> Clock Set Count, the number  of times camera clock changed.
UnderCut Cnt: 0 -> Under-Cut  Count.
RTC Read Err: 0 -> Real-time clock read error  count, the number of read errors of RTC.

3. Press the same button  combination again, the camera will return to the normal display.

Also noted is the process to be rid of the yellow triangle with an exclamation mark inside that appears when you  turn off the camera. According to Wiórek,  the yellow triangle appears when the firmware is not set to any of  specific regional models. Some of us have gotten this after upgrading to particular firmware, and of course they don't have any answers at panasonic support.  Contact me for details!

经不住诱惑，二手购入
试片
感觉出片多少有点欠曝
色温不是很准，有点偏冷
焦外颗粒感很夸张，尤其是暗部

手感很棒，操作很传统

胖大再次出现了哈

吃饱喝足出门后咔嚓一张：

[胖大 编辑于 2010-03-24 23:22]

没啥可拍的，对着公司外咔嚓一张：

多少银子出？

美女的3张片是阴天拍的？

看图

再来

"打秋千"

没意外，我用偶尔717，LX1拍出比L1好的片，没办法，自己水平太水了，就是玩机器了。

关键是,要油.其次在于,视角.14-50不可能拍那么近.但是,我上的第1张是微距王尼康E4500拍d.有点意外吧.

月初在天台遛狗的时候顺便捏了下快门。动态黑白模式，只缩小。

回美女（真是美女？）我眼拙，看不出哪个是L1拍的。瞎猜一下，第一张。

猜一下,看哪张上L1拍的,第2张

猜一下,看哪张上L1拍的

没光线，看不出油来。

我也想要台

梨花,看一下油不油.

"I see dead people", 有人能象sixth sense里面那个小孩一样看到正常人看不到的东西, 也是可能的.

哪里有DC味呢？

没觉得象DC啊,N和C的机器我都用过,要说高ISO下表现不如NC倒是,DC味还真没感觉出来.

胖大的好片真多，给咱详细说说拍摄设置和后期处理吧。

我只是想说N或C的成像，没讨论谁造的

都说是sony提供的，但两家的风格差距很大呢
CN我都喜欢，但不能用，L1,G1,我都不喜欢，但必须要用~~~~
不过GF1+45/2.8相当不错的！！

N芯？你说的是N单反的芯？你确定是N做的吗？